To turn the 7-way on your truck into a 12v power source you will want to use the Pollak 7-Way to 12 Volt Power Outlet Adapter item # PK11896. This will plug into a 7-Way on your vehicle and provide a 12V plug on the other end that can be used with 12V accessories. This adapter can handle a 20 to 30 amp power draw but the limiting factor will be if the 7-Way on your truck is rated high enough as well. You will want to check the fuse for the 12 volt circuit for the tow package trailer connector... view full answer...
The Converter for Parallax/Magnetek or WFCO RV Power Centers # PD4645V is rated for 45 amps of 12 volt power with up to 610 watts of output power. This is roughly the same amount of input wattage or about 5.1 amps of 120 volt power at maximum draw. Since the power from the converter is mostly used for charging the 12 volt battery and supplying power to the 12 volt lights, slide motors, power awning, and any other 12 volt components on your trailer it will often only be pulling much less... view full answer...
Yes, most 12 volt accessory circuits that 7-ways have are rated for 40 amps so a 7.5 amp draw would not be an issue at all.
I attached a help article with trailer wiring diagrams for you to check out as well. view full answer...
I have a solution for you but the only way to power accessory lighting in your trailer through a 12v is to use an adapter like the Pollak 7-Way to 12 Volt Power Outlet Adapter item # PK11896. It sounds like you already have one of these. This will turn your 7-way connector into a 12v power source. Once you have a 12v connector on your 7-way you will want to purchase an adapter that has two male 12v ends. There isn't a 7-way trailer connector to a 12v male connector adapter. The reason there... view full answer...
Sometimes that circuit isn't active. The easy answer would be to run a length of 10 gauge wire like part # 10-1-1 through a breaker like the part # 9510 to the positive terminal of your truck battery.
With some Ram trucks if trailer circuits have fuses blow the only way to reset it is to take it to a dealer which is frustrating. view full answer...
You are correct a wire ran from the 12 volt accessory circuit of you 7-way to the positive post of the battery will keep a maintenance charge on it. This will keep the battery topped off but would not bring a totally dead battery back to life.
You would want to use 10 gauge wire like part # 10-1-1 for this. view full answer...
Yes, once you install the Tekonsha Harness # 118253 the 12 volt accessory circuit would be activated which would allow you to install a RF Brake Controller part # TK94FR.
I attached install videos for both products for you to check out. view full answer...
The Phoenix Electric Trailer Jack # UF38-944040 internally has a 30 amp slow blow fuse for circuit protection so that would be the rating breaker you would want to use. view full answer...
I'll start off by saying that lumens is a measurement of the light that is given off by a particular light and not a measurement of energy usage. When it comes to determining the wattage, that is calculated by multiplying the amp draw multiplied by the voltage of the power supply (Formula is: Current (a) x Voltage (v) = Power (w)).
The Opti-Brite 12v/24v LED Dome Light # ILL08COB uses 1.61 amps on 12.8v power and 0.8 amps on 24v power. When you use these numbers, on a 12.8v power supply... view full answer...
In regards to mounting the 63 inch Solera Smart Arm 12V Power RV Awning Conversion Kit, Lippert has told us the wall-mounted brackets require a minimum width of 2-1/2 inches for installation, but that at least a 3 inch width would be preferred.
That is true for the width of the brackets for both colors of the conversion kit:
- Black: Solera Smart Arm 12V Power RV Awning Conversion Kit # LC759516
- White: Solera Smart Arm 12V Power RV Awning Conversion Kit # LC759404 view full answer...
The bottom mounting holes for the Jensen LED RV TV - 1080P - 1 HMDI - 12 Volts - 24" Screen # JEN46VR are approximately 5" from the bottom the of the tv. The mounting holes are spaced 3.94" apart side-to-side and top-to-bottom. I can't confirm that another brands 12v cable will have the correct connection for the tv but I can confirm that the Power Adapter Cord for Jensen LED Televisions - 12V DC # DCCIG09 will work with this tv to power it through a 12v "cigarette lighter" port. view full answer...
It's a pain and we get this question daily but the only way to power the Curt T-Connector Vehicle Wiring Harness item # C56093, and not damage your Taurus or void the harnesses warranty, is to run a direct line to the battery. The tail light converter needs to be powered by a direct 12v line to your battery to function correctly.
The Curt T-Connector Vehicle Wiring Harness item # C56093 is custom fit for your 2018 Ford Taurus. It plugs into your Taurus's wiring harness, which is located... view full answer...
The TorkLift PowerArmor Locking Battery Box - 6V and 12V Batteries part # TLA7712R is 8 1/4" wide and 23 15/16" long. I have included a photo with dimension lines on it for you to check out. view full answer...
To charge your gooseneck trailer batteries and power your accessories you're going to need the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 25 Amp item # 331-BCDC1225D. You are also going to want the 40-Amp MIDI Fuse Kit for Redarc In-Vehicle 25-Amp BCDC Battery Charger item # 331-FK40 to connect to your battery and the Universal Mounting Bracket for Redarc BCDC Battery Charger item # RED53FR for installation.
This charger can use both your vehicle battery... view full answer...
All our Solera 12V XL Power RV Awnings are 9 feet 8 inches long. Meaning, the canopy extends 9'8" from your RV when fully extended and the Item # LCV000334919-362241 has a 12 foot long tube that will attach to your RV. I've Included a couple videos about these awnings if you would like to learn more! view full answer...
Yes, you can charge two 12v batteries when they are connected in parallel using the Go Power RV Converter and Smart Battery Charger item # 34266167. 35 amps are more then enough to charge your batteries in parallel. However, it will take longer to charge the batteries when they are connected compared to if you were to charge each one separately. view full answer...
A 12V trailer power circuit will typically be wired with 12-gauge wire, part # 12-1-1, but certainly there is no harm in using heavier 10-gauge wire # 10-1-1. If one tow vehicle is longer than another, our installers may opt to use the heavier gauge wiring than they would for a physically shorter vehicle. When in doubt you can always use 10-gauge. view full answer...
Yes, the Gustafson RV LED Pendant Light # 277-000422 is an LED Light designed to work on the 12v power supplied by your RV battery. This 5" diameter light is going to provide a bright, focused light perfect for your kitchen or over a dining table. When installing it, you'll need to keep the old hardware from the light you're removing, since this light does not come with any mounting screws. view full answer...
The Go Power Industrial Pure Sine Wave Inverter - GFCI - 2,000 Watt - 12V, part # 34278156, measures 17-7/16" long x 9-3/4" wide x 3-1/4" tall.
I have included a video review link for this item below. view full answer...
The Rear View Safety Cigarette Lighter Adapter # RVS-505 measures 9-1/2" from the tip of the wires to the start of the 12v cigarette lighter, additionally this adapter also has an overall length of 13".
Attached is a diagram that shows these measurements as well. view full answer...
Go To Results